Skip to main content

3-Phase Alternator

3-Phase Alternator


A 3-phase alternator is a synchronous machine that changes over mechanical power into 3 control through the procedure of electromagnetic induction.

A 3-Phase alternator works on the indistinguishable key rule of electromagnetic enlistment from a d.c. generator for example right when the movement interfacing a conductor changes, an e.m.f. is actuated in the conductor. Like a d.c. generator, a 3-arrange alternator similarly has a nature winding and a field winding. Review that e.m.f. incited in the armature twisting of a d.c. the generator is substituting voltage and is changed over to coordinate voltage by the commutator titted on the pole of the generator. Be that as it may, In a.c. generator or alternator, the commutator can be supplanted by a lot of slip rings and the rotating voltage produced in the armature winding can be connected to the outer burden through the slip rings. Be that as it may, essentially there is one imperative distinction between the two. In a d.c. generator, the armature winding is set on the rotor to encourage substitution and the field shafts are put on the stator (stationary part) of the machine. Since no commutator is required in an alternator it is commonly dynamically supportive and ideal to put the field bending on the turning part (i.e. rotor) and armature twisting on the stationary part (for example stator) has appeared in Figure 22.1.


3-Phase Alternator Diagram





[caption id="attachment_981" align="alignnone" width="1956"]3-Phase Alternator  3-Phase Alternator[/caption]

Read More

Earth Pressures




Popular posts from this blog

Limitations of Terzaghi Theory

Limitations of Terzaghi Theory The value of the coefficient of consolidation has been assumed to be constant.  The distance d of the drainage path cannot be measured accurately in the field. The thickness of the deposit is generally variable, and an average value has to be estimated.  There is sometimes difficulty 1n locating the drainage face, sometimes thin previous seams that can act as good drainage face are missed in the boring operations. The equation is based on the assumption that the consolidation is one-dimensional. In the field, the consolidation is generally 3-dimensional. The lateral drainage may have a significant effect on the time rate of consolidation. The initial consolidation and secondary consolidation have been neglected. Sometimes these form an important part of the total consolidation. In actual practice, the pressure distribution may be far from linear or uniform. Read More Muller-Breslau principle

Price Guard Wire Method

Price Guard Wire Method Some form of  Price Guard Wire Method  is generally used to eliminate the errors caused by leakage currents over insulation. Fig. 3.14 illustrates the operation of This Method. In fig 3.14(a), a high resistance mounted on a piece of insulating material is measured by the ammeter voltmeter method. The micro-ammeter measures the sum of the current through the resistor (IR) and the current through the leakage path around the resistor. The measured value of resistance computed from the readings indicated on the voltmeter and the microammeter, will not be a true value but will be in error.   Figure 3.14 Application of  guard  circuit for measurement of high resistance In fig, 3.14 (b), the  guard  terminal has been added to the resistance terminal block. The  guard  terminal surrounds the resistance terminal entirely and is connected to the battery side of the micro-ammeter. The leakage current IL now

Negative Booster

Negative booster A negative booster is employed to conform to the regulation that the potential difference between any two points of the rail return shall not exceed 7 V. Two boosters, positive and negative, are used which are mechanically coupled together and driven by a DC motor. The positive booster is connected to the trolley wire (near the generating station) and the negative booster (separately excited) is connected to the track rail.  The 'positive booster' adds voltage to the line while the 'negative booster lowers the potential of the point it is connected to. As we go along the trolley wire away from the generating station/sub-station, the potential drop increases, and the voltage of the trolley wire falls. Since the current returns via the track rail points away from the generating station acquire high potentials. This potential is brought down by the negative boost provided by the negative booster. When the load is sufficiently far aw